Optical-Module Parameter Inquiry and Alarm Configuration
The following command shows how to enable the transmitting optical power alarm on port e8/1, set the maximum and minimum values, and clear the alarm thresholds.
Optical-Module Parameter In
1.4.2 Example of Setting the OLT Optical-Module Alarm The following example shows how to enable the light transmission power alarm on port e0/1, set the minimum and maximum values, and clear the
ALM-303046923 AP Optical Remove_WAC&AP Alarms_Device
Description WLAN/4/AP_OPTICAL_REMOVE:OID AP optical remove. (APMAC= , APName= , IfIndex= , ApEntityPhysicalName= , APID=
22-Optical Module Parameter Inquiry and Alarm
22-Optical Module Parameter Inquiry and Alarm Configuration - Free download as PDF File (.pdf), Text File (.txt) or read online for free.
Setting Optical Power Alarm Thresholds
The default optical power alarm thresholds of an optical module are fixed and cannot be changed. These thresholds are determined through extensive testing and verification. You can configure alarm
DEVM/1/hwOpticalRemove_active
Procedure 1. Insert the corresponding optical module and check whether the alarm is cleared.
DEVM/1/hwOpticalRemove_active
This document describes the logs supported by the device, including the log message, description, parameters, possible causes, and handling procedure.
GPON System Parameters
GPON System Optical Parameter Detection provides information about optical parameter diagnosis and the GPON port optical parameter threshold. It is mainly used to query the alarm monitoring of GPON
Setting Optical Power Alarm Thresholds
An optical module has default optical power alarm thresholds, which are fixed and cannot be changed. The configured optical power alarm thresholds must be within the default range.
Disabling the Optical Module Alarm Function
The device has two types of optical module power alarms: warning and alarm. A warning is reported when the difference between the actual power and vendor-defined threshold is not great. It can also
NetEngine AR5700, AR6700, and AR8000 V600R024C00 Alarm
Procedure 1. Insert the corresponding optical module and check whether the alarm is cleared. If the alarm is cleared, go to Step 3. If the alarm persists, go to Step 2. 2. Collect alarm, log,
Configuring the Alarm Function for Optical Modules
You can configure the alarm thresholds for the power of optical modules to shield unnecessary alarms. To check alarm information, diagnostic information, and manufacturing information about an optical
Huawei Technical Support
Huawei Technical Support
Optical module alarm
Check the diagnostic information, which shows that the received optical power is low, with a threshold of -3 to -23.01, currently at -22.84. Once it exceeds the threshold, an alarm will be
DEVM/1/hwOpticalRemove_active
Check whether the interface where the optical module is installed has been used. If not, ignore this alarm. If so, install the corresponding optical module.
Disabling the Optical Module Alarm Function
Context The system automatically obtains the vendor-defined power threshold of an optical module and compares it with the actual power. If the actual power exceeds the vendor-defined threshold, an
Optical-Module Parameter Inquiry and Alarm Configuration
The parameters of optical module include the light transmission power, the light reception power, the temperature, the power-supply voltage and the bias current.
Optical-ModuleParameterInquiryandAlarm Commands
The correct alarm information can be generated only when the global optical module parameter monitoring function is enabled (that is, global configuration ddm enable).
System Management Configuration, Cisco Catalyst PON Series
GPON System Optical Parameter Detection provides information about optical parameter diagnosis and the GPON port optical parameter threshold. It is mainly used to query the alarm
Configuring the Alarm Function for Non-Huawei-Certified Optical Modules
This facilitates optical module management and maintenance. Additionally, vendor information of optical modules early delivered from Huawei may not be recorded. When these optical
Checking the Working Modes
Procedure Run the display transceiver interface interface-type interface-number verbose command to view the optical module parameter settings. All the parameters of each optical module
ALM-650074 Switch Optical Module has been removed
Check whether the interface where the optical module is installed has been used. If not, ignore this alarm. If so, install the corresponding optical module. To ignore and clear this alarm, run the clear
DEVM/1/hwOpticalRemove_active
1. Insert the corresponding optical module and check whether the alarm is cleared. If the alarm is cleared, go to Step 3. If the alarm persists, go to Step 2. 2. Collect alarm, log, and configuration
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.4.1 hwOpticalRemove
AR500, AR510, AR531, AR550, AR1500, and AR2500 V200R010 Alarm Handling This document provides the trap description, attributes, parameters, impact on the system, possible
ALM-303046682 An Optical Module Was Removed from the AP
ALM-303046682 An Optical Module Was Removed from the AP Updated on 2024-01-25 GMT+08:00 On this page Description Attribute Parameters Impact on the System Possible Causes
Related Resources
- US Enterprise-Grade 25G Optical Router
- Price of fire-resistant cable tray boards
- Fiber optic cable for dedicated fiber optic equipment
- 82599 Optical Module
- Flat Angle Bend Cable Tray
- Czech Edge Data Center 19-inch
- Zimbabwe Antioxidant Cable Tray Supplier
- Uplink and downlink ports of the optical splitter
- Case Study of Fiber Optic Tubing Installation in Columbia Data Center
- Intelligent PDU Installation Process
- Botswana Certified CFP82 5G
- Three-level distribution box connection point
- Customized Flame-Retardant Cable Trays for Somalia
- Should the ground wire be connected to the distribution box
- Patch Cord Fiber Optic Cable
- Ranking of seismic-resistant cable tray supports